Panduan Service Fotocopy Canon

By photocopy canon | At Friday, March 15, 2013 | Label : IR , IR 5050 , iR5570 , iR6570 , Kode Error Fotocopy , Panduan Fotocopy | 1 Comments

Panduan Service Fotocopy Canon IR6570, 5050, 5070, 5570, 5075 ini mungkin bagi Teknisi Fotocopy hal ini kecil dan gampang untuk memperbaikinya untuk itu sengaja saya rekomendasikan  bagi pemula atau mereka yang ingin baru "Belajar Service Fotocopy Canon".

Panduan Service Fotocopy Canon masalahnya menurut sumber dari master kita di Facebook (Klik aja fbnya kl pgn tau) :

Akibat-akibat yang akan ditimbulkan apabila bearing Lower Roll Canon IR (typenya tersebut diatas)  bermasalah ataupun rusak sbb:

1. Error E014. Error ini dikarenakan putaran pada motor pemanas yang abnormal atau tidak sesuai, sehingga sensor akan mendeteksi adanya kerusakan pada bagian Motor Pemanas ini.
2. Error E001. Error ini dikarenakan rusak atau lepasnya ring pengunci pada Upper Roll. Fungsi ring ini adalah untuk mengunci agar roda gigi pada upper roll tidak lepas. Dengan rusaknya ring ini akan menyebabkan perputaran upper roll tidak normal, sehingga terjadilah error E001 ini.

Dengan mengetahui akibat-akibat yang akan terjadi apabila bearing Lower Roll Canon IR ini tidak bekerja sebagai mana mestinya, ada baiknya untuk memeriksa secara berkala bearing-bering pada Mesin Fotocopy anda khususnya pada bagian Lower roll di fixing unit.

Panduan Service Fotocopy Canon ini hanyalah sebagian kecil dari Permasalahan-permasalahan yang terjadi di Mesin Fotocopy Canon anda, untuk itu rawatlah dengan baik mesin anda agar bisa dipakai secara optimal dan tentunya untuk jangka panjang

Bagi Teknisi Canon yang sudah merasa Expert, banyak-banyaklah berbagi jangan takut rejeki atau pendapatan anda berkurang justru kelak anda akan ditambahkan lebih banyak dari apa yang anda duga, by copasdotkom. hehehe.... jd malu eui

Sekian dahulu pembahasan kita kali ini tentang Panduan Service Fotocopy Canon apabila bermanfaat jangan lupa klik tombol suka diatas dan please dong tanggapannya lewat komentar dibawah .........

Kode Error Fuji Xerox

By photocopy canon | At Tuesday, February 12, 2013 | Label : Fuji Xerox , Kode Error Fotocopy , photocopy canon | 3 Comments

Berikut ini saya bagikan Daftar Kode Error Fuji Xerox lengkap, sebagai panduan anda mencari kode kerusakan yang sering terjadi.

Demikian Kode Error Fuji Xerox ini saya bagikan ke anda mudah-mudahan bermanfaat.

Kode Error Canon IR2200/IR2800/IR3300

By photocopy canon | At Friday, December 07, 2012 | Label : Canon Image Runner , Download , Kode Error Fotocopy , Manual Service Fotocopy , Panduan Fotocopy , photocopy canon | 0 Comments

Download Kode Error Canon IR3300 IR2800 IR2200 dan Download Service Manual Canon IR3300 IR2800 IR2200 lewat link diakhir artikel ini.

Code	Subcode	Description
E000	0000	The reading of the main thermistor does not reach 30oC 1 sec after the main power switch is turned on. Or, it does not reach 70oC 2 sec thereafter
E001	0000	The main thermistor detects 250oC or higher
	0001	The main thermistor or the sub thermistor detects overheating (hardware circuit detection)
	0002	The sub thermistor detects about 295oC or higher
E002	0000	The temperature of the fixing film is as follows: has exceeded 100oC, but does not reach 115oC within 1 sec thereafter. has exceeded 140oC, but does not reach 150oC within 1 sec thereafter. has exceeded 160oC, but does not reach 165oC within 1 sec thereafter
E003	0000	The main thermistor reading is lower than 140oC when paper is moved
	0001	Low fixing temperature detection after standby (by sub thermistor)
E007	0000	An error in the rotation of the fixing film is detected. The reading of the main thermistor is 100oC or higher and, in addition, the fixing film sensor does not detect the rotation of the film for 6 sec or more while the fixing motor is driven
E010	0000	After the main motor drive signal is generated, the clock signal does to arrive within 1.3 sec
E014	000	After the fixing motor drive signal is generated, the clock signal does not arrive within 1.3 sec
E019	0000	The waste toner case is full of waste toner
E032	0001	The DA unit connection is disconnected (after connection).
E051	0000	At start-up, home position is not detected when the horizontal registration assembly is moved 100 mm in the direction of home position
E064	0000	The presence of a high-voltage error is communicated by the composite power supply PCB (The output for primary charging, developing, or transfer has deviated from a specific level of voltage)
E100	0001	The BD signal is not detected 10 times or more within 10 msec in 5 msec after the generation of the laser drive signal
	0001	The BD signal is not detected 10 times or more within 10 msec in 5 msec after the generation of the laser drive signal
	0002	While the laser is ON, the BD signal cycle is outside a specific range 20 times or more continuously
	0003	While the laser is ON, the horizontal sync signal cycle is outside a specific range 20 times or more
E110	0000	The motor ready signal does not arrive within 15 sec after the laser scanner motor drive signal is generated
E202	0001	The scanner home position sensor does not go OFF when the scanner is moved forward by 40 mm
	0002	The scanner home position sensor does not go ON when the scanner is moved reverse 450 mm
E204	0001	While an original is being read, the image leading edge signal does not arrive from the ADF
E220	0001	A fault is detected on the inverter PCB for the scanning lamp
E225	0000	A specific level cannot be attained for the signal during CCD gain correction at power-on
	0002	The edge gain correction level is different from the correction level for the preceding sheet by a specific level or more
E240	0000	A fault occurs in communication between the CPU of the main controller PCB and the CPU of the DC controller PCB
E243	0000	A fault occurs in the communication between the CPU of the control panel PCB and the CPU of the main controller PCB
E248	0001	A difference is discovered between the ID in EEPROM read when the main power switch is turned on and the ID in ROM upon comparison
	0002	The data read does not match the data written to EEPROM
	0003	A difference is discovered between the ID of EEPROM and the ID of ROM upon comparison while writing data
E261	0000	The intervals of zero-cross signals deviate from the tolerance range while the fixing heater is supplied with power
E302	0001	During shading, the shading processing does not end on the reader controller PCB after 1 sec
	0002	During stream reading, the edge white addition processing does not end on the rear controller PCB after 10 sec
E315	-	Any of the following is true in the image processing by the main controller: The image data has a fault The encoding/decoding operation for image data has a fault The image processing element of the main controller PCB has a fault
E601	0000	When an image is transferred between the main controller PCB and the HDD, the main controller PCB detects a fault in control information
	0001	When an image is transferred between the main controller PCB and the DC controller PCB, the DC controller PCB detects a fault in the control information
E602	0001	A mounting fault of the HDD is detected when the HDD is started up from the BOOT ROM
	0002	A data read fault of the HDD is detected when the HDD is started up from the BOOT ROM
E604	0000	A fault is detected in the image memory
E605	0001	A fault is detected in the battery for the image memory
E606	0001	A mounting fault of the HDD is detected when the HDD is started up from the BOOT ROM
E674	0000	A faulty occurs in the communication between the fax PCB and the main controller PCB
E677	0001	A fault occurs it the combination between any of the printer boards (accessories) and the main controller PCB
E710	0001	When the main power is turned on, the communication IC (IPC) on the reader controller PCB cannot be initialized
	0002	When the main power is turned on, the communication IC (IPC) on the DC controller PCB cannot be initialized
	0003	When the main power is trend on, the communication IC (IPC) on the main controller PCB cannot be initialized
E711	0001	Data is written to the error register of the communication IC (IPC) on the reader controller PCB four times or more within 1.5 sec
	0002	Data is written to the error register of the communication IC (IPC) on the DC controller PCB four times or more within 2 sec
	0003	Data is written to the error register of the communication IC (IPC) on the main controller PCB four times or more within 2 sec
E712	0001	The communication is not resumed 3 sec or more after data has been written to the error register of the communication IC (IPC) on the ADF controller PCB
	0002	The transmission bit is not enabled 10 sec or more in the sync register of the communication IC (IPC) on e reader controller PCB
E713	0000	The communication with the finisher is not resumed 3 sec or more after it is disrupted
E716	0000	The ID signal is not detected within a specific period of time after the presence of a pedestal is detected
E719	0000	Erroneous communication with card reader (serial communication)
	0002	Erroneous communication with coin vender (serial communication)
E717	0001	The communication with the DA unit is not resumed 3 sec or more after it is disrupted
E719	0001	The communication between the Card Reader-C1 or the coin vendor and the main controller PCB is disrupted
E732	0001	A fault is detected by the main controller PCB in the communication between reader controller PCB and the main controller PCB
E733	0001	A fault is detected by the main controller PCB in the communication between the DC controller PCB and the main controller PCB
E737	0000	During self diagnosis at power-on, the DRAM check finds a fault in the main controller PCB
E740	0001	At power-on, the LAN card has a fault
	0002	The MAC address has a fault
	0003	The LAN card cannot be read
E741	0000	The PCI bus has a fault
E743	0000	The reader controller PCB detects a fault in the communication between the main controller PCB and the reader controller PCB
E744	0000	The BootROM on the main controller PCB and the system software are for different models or are of different types
E803	0000	The 24V output from the composite main power supply PCB is absent for 1 sec or more
E805		The clock signal is absent for 5 sec or more after the fan drive signal has been generated. The detail codes of the fans in question are as follows:
	0001	developing fan (FM1)
	0002	fixing fan (FM2)
	0003	curl reducing fan (FM4)
	0004	curl reducing fan (FM5)
	0005	electrical unit fan (FM3)
E901	0000	The motor ready signal does not arrive within 1.3 sec after the pedestal main motor drive signal is generated
ADF Error Codes
E420	0001	When the power switch of the host machine is turned on, the back-up data from the EEPROM cannot be read or the data that has been read has a fault
E421	0001	The back-up data cannot be written to the EEPROM, or the data that has been written has a fault
E422	0001	While the ADF is in standby, the communication with its host machine is disrupted for 5 sec or more; or, while the ADF is in operation, the communication with its host machine is disrupted for 0.5 sec or more
Saddle Finisher-G1 Error Codes
E501	0001	The communication between the finisher controller PCB and the puncher drive PCB is disrupted
E505	0001	When the main power is turned on, the checksum of the finisher controller PCB has a fault
	0002	When the main power is turned on, the checksum of the puncher driverPCB has a fault
E510	0001	The feeding roller does not leave home position when the feed motor is driven for 2 sec
	0002	The feeding roller does not return to home position when the feed motor is driven for 2 sec
E514	0001	The delivery belt does not leave home position when the stack delivery motor is driven for 3 sec
	0002	The delivery belt does not return to home position when the stack delivery motor is driven for 3 sec
E530	0001	The aligning plate (rear) does not leave home position when the alignment motor (rear) is driven for 3 sec
	0002	The aligning plate (rear) does not return to home position when the alignment motor (rear) is driven for 3 sec
E531	0001	The stapler does no leave home position when the stapler/folder motor is driven for 1.5 sec
	0002	The stapler does not return to home position when the stapler/folder motor is driven for 1.5 sec
	0003	The clock signal is disrupted for 1 sec or more while the stapler/folder motor is driven
E532	0001	The stapler unit does not leave home position when the stapler slide motor is driven for 4.5 sec
	0002	The stapler unit does not return to home position when the stapler slide motor is driven for 4.5 sec
E537	0001	The aligning plate (front) does not leave home position when the alignment motor (front) is driven for 3 sec
	0002	The aligning plate (front) does not return to home potion when the alignment motor (front) is driven for 3 sec
E540	0001	The paper surface sensor remains unchanged 10 sec after the tray ascent/ descent motor is driven
	0002	The tray upper sensor goes ON while the tray is moving up.
	0003	The clock for the clock sensor is disrupted for 10 sec or more while the tray ascent/descent motor is driven
E577	0001	The paddle does not leave home position when the paddle motor is driven for 2 sec or more
	0002	The paddle does not return to home position when the paddle motor is driven for 2 sec or more
	0003	The stack ascent/descent guide does not leave home position when the paddle motor is driven for 2 sec or more
	0004	The stack ascent/descent guide does not return to home position when the paddle motor is driven for 2 sec or more
E590	0001	The puncher does not return to home position when the puncher motor is driven for 250 msec
	0002	The clock from the puncher motor clock sensor is disrupted for 60 msec or more when the puncher motor is driven
E592		In the course of sensor output automatic adjustment, the light-receiving voltage is 2.5 V or less even when the light-emitting voltage is set to 4.4 V. In the course of output automatic adjustment, the light-receiving voltage is 2.5 V or more even when the light-emitting voltage is set to 0 V. In the course of sensor output automatic adjustment, the light-emitting voltage is set to 4.4 V or more
	0001 to 0005	Horizontal registration sensor
	0006	Puncher waste full sensor
E593	0001	The puncher not leave home position when the puncher shift motor is driven for 1 sec
	0002	The puncher does not return to home position when the puncher shift motor is driven for 1 sec
E5F1	0001	The folding roller does not leave home position when the stapler/folder motor is driven for 1.5 sec
	0002	The folding roller does to return to home position when the stapler/folder motor is driven for 3.5 sec or more
	0003	The clock is disrupted for 1 sec or more while the stapler/folder motor is driven
Finisher-J1 Error Codes
E500	0000	The communication between the copier and the finisher is disrupted and is not corrected for 5 sec or less
E514	0000	At the start of the motor CW operation, the stack handling motor (M2) may be driven for a specific number of rotations; however, the stack delivery lever home position sensor (S8) does not go ON
E530	0000	The alignment motor (M4) is driven for a specific number of rotations, but the aligning plate home position sensor (S7) does not go ON. The alignment motor (M4) is driven for a specific number of rotations, but the aligning plate home position sensor (S7) does not go OFF
E531	0000	The stapling home position sensor (S16) does not go off 0.5 sec after the stapler motor is rotated CW. The stapling home position sensor (S16) dos not go ON with 0.5 sec after the stapler motor is rotated CW and, thereafter, the sensor does not go ON within 0.5 sec after the motor is rotated in reverse
E537	0000	The aligning plate home position sensor (S6) does not go ON when the front alignment motor (M3) is driven for a specific number of rotations. The aligning plate home position sensor (S6) does not go OFF when the front alignment motor (M3) is driven for a specific number of rotations
E577	0000	The return roller does not reach home position when the delivery motor (Ml) has been driven as much as will move it to the return roller home position sensor (S3)
E580	0000	The delivery tray upper limit sensor (S13) goes ON while the delivery tray ascent/descent motor (M5) is in operation. The clock signal of the delivery tray ascent/descent motor clock sensor (S9) is not detected 15 times or more within 0.8 sec while the delivery tray ascent/ descent motor (M5) is in operation. The delivery tray paper height sensor (S10) does not go ON 4 sec after the delivery tray ascent/descent motor (M5) starts to move up. The delivery tray paper height sensor (S10) does not go OFF 4 sec after the delivery tray ascent/descent motor (M5) starts to move down
E585	0000	At the start of the motor CCW operation, the stack handling motor (M2) may be driven for a specific number of rotations; however, the stack delivery lever home position sensor (S8) does not go ON

Ok semoga Error Codes dan Service Manual Canon IR3300 IR2800 IR2200 ini bisa menjadi Panduan Service Fotocopy Canon Imagerunner atau Mesin Fotocopy IR anda.

Download iR2200 iR2800 iR3300 Service Manual

Kode Error Mesin Fotocopy Ricoh

By photocopy canon | At Thursday, November 15, 2012 | Label : Kode Error Fotocopy , photocopy canon , Ricoh | 0 Comments

Ricoh GR Digital II FirmwareUpdate V2.0 (Photo credit: takuhitosotome)

Kode Error Mesin Fotocopy Ricoh [Error Codes Ricoh Copier] atau Technical SC CODE Ricoh adalah suatuh keadaan dimana Mesin Photocopy Ricoh memberitahukan letak kesalahan atau system error pada mesin fotocopy khususnya merek RICOH analog.



Dibawah ini saya berikan Kode Service [kode Error] Mesin RICOH Analog FT 7650

1.1 EXPOSURE

SC 101 - Exposure lamp malfunction - abnormal On/Off
Definition: [level: A]
During the lamp off condition, the optics control board detects a lamp voltage.

Possible causes
• Exposure lamp open
• Triac shorted
• Exposure lamp thermoswitch open
• Optics control board defective

SC 103 - Power source frequency detection error
Definition: [level: D]
Detects frequencies out of the 45Hz to 65Hz range.

Possible causes:
• Abnormal power source
• Electrical noise
• AC drive board defective
• Optics control board defective

SC  104 - Exposure lamp malfunction - abnormal off
Definition: [level: D]
The scanner start signal is received even if the main relay off condition is detected.

Possible causes:
• Main relay defective
• Communication error between the main control board and the optics control board because of a poor harness connection.
• Optics control board defective

Troubleshooting
1.2 SCANNER

SC 120 - Scanner home position sensor abnormal - stays off
Definition: [level: D]
The scanner home position sensor does not detect the on condition even if the scanner returns home.

Possible causes:
• Scanner home position sensor defective
• Optics control board defective

SC 121 - Scanner home position sensor abnormal - stays on
Definition: [level: D]
The scanner home position sensor does not detect the off condition even if the scanner leaves the scanner home position sensor by 120 mm.

Possible causes:
• Scanner home position sensor defective
• Scanner motor defective
• Scanner HP sensor short

SC 125 - Low scanner speed
Definition: [level: D]
The scanner speed, detected by the optics control board through the encoder, is lower than the specified speed.

Possible causes:
• Scanner drive motor defective
• Optics Control Board defective

SC 126 - High scanner speed
Definition: [level: D]
The scanner speed, detected by the optics control board through the encoder, is higher than the specified speed.

Possible causes:
• Scanner drive motor defective
• Optics control board defective

SC 127 - Scanner drive motor encoder failure
Definition: [level: D]
Scanner rotating direction detected by the optics control board through the encoder is opposite to the specified direction.

Possible causes:
• Scanner drive motor defective
• Optics control board defective

1.3 LENS MAGNIFICATION

SC 140 - Lens vertical home position sensor abnormal - stays off
Definition: [level: D]
When the lens returns to the home position, the lens vertical home position sensor does not detect the on condition for 2 seconds or more, and more than twice.

Possible causes:
• Lens vertical home position sensor shorted
• Lens vertical drive motor defective
• Optics control board defective

SC 141 - Lens vertical home position sensor abnormal - stays on
Definition: [level: D]
When the lens returns to the home position, the lens vertical home position sensor does not detect the off condition for 3.5 seconds or more, and more than twice.

Possible causes:
• Lens vertical home position sensor open
• Lens vertical drive motor defective
• Optics control board defective

SC 142 - Lens horizontal home position sensor abnormal - stays off
Definition: [level: D]
When the lens returns to the home position, the lens horizontal home potion sensor does not detect the on condition for 1.7 seconds or more, and more than twice.

Possible causes:
• Lens horizontal home position sensor short
• Lens horizontal drive motor defective
• Optics control board defective

SC 143 - Lens horizontal home position sensor abnormal - stays on
Definition: [level : D]
When the lens leaves from the home position, the lens horizontal home potion sensor does not detect the off condition for 2.3 seconds or more, and more than twice.

Possible causes:
• Lens horizontal home position sensor open
• Lens horizontal drive motor defective
• Optics control board defective

Troubleshooting
SC 144 - 3rd scanner home position sensor abnormal - stays off
Definition: [level: D]
When the 3rd scanner returns to the home position, the 3rd scanner home position sensor does not detect the on condition for 1.2 seconds or more, and more than twice.

Possible causes:
• 3rd scanner home position sensor shorted
• 3rd scanner drive motor defective
• Optics control board defective

SC 145 - 3rd scanner home position sensor abnormal - stays on
Definition: [level: D]
When the 3rd scanner leaves from the home position the 3rd scanner home position sensor does not detect the off condition for 2.0 seconds or more, and more than twice.

Possible causes:
• 3rd scanner home position sensor open
• 3rd scanner drive motor defective
• Optics control board defective

SC 146 - Abnormal magnification operation
Definition: [level: D]
The lens vertical drive motor or the lens horizontal drive motor move for no apparent reason in the ready condition.

Possible causes:
• Lens vertical drive motor defective
• Lens horizontal drive motor defective
• 3rd scanner drive motor defective
• Optics control board defective

1.4 OPTICS THERMISTOR

SC 190 - Optics thermistor open
Definition: [level: D]
The optics thermistor is open.

Possible causes:
• Optics thermistor open
NOTE: When the optics thermistor is shorted, no SC code is indicated. The exhaust fan rotates quickly and continuously.

SC 191 - Scanner motor thermistor open
Definition: [level: D]
The scanner motor thermistor is open.

Possible causes:
• Scanner drive motor defective

SC 192 - High Scanner Motor Temperature (70 CPM)
Definition: [level: D]
The temperature of the scanner motor is 80°C or more.

Possible causes:
• Scanner motor clooing fan defective

1.5 MAIN CHARGE

SC 302 - Charge corona leakage
Definition: [level: D]
The charge power pack detects a charge corona leakage (output: 0 V) for 4.8 ms, or detects the output to be more than 7 kV, 10 times in one job.

Possible causes:
• Main charge corona unit defective
• Main charge power pack defective
• High voltage control board defective

SC 303 - Charge corona wire cleaner failure
Definition: [level: C]
The current of the charge corona wire cleaner drive motor is over the specified current within 4 seconds after the cleaner motor starts. The charge corona wire cleaner does not move back to the end block within 30 seconds.

Possible causes:
• Charge corona wire cleaner drive motor defective
• Insufficient lubrication for the charge corona wire cleaner drive mechanism (G501 grease)
• High voltage control board defective

1.6 DEVELOPMENT

SC 341 - Development motor locked
Definition: [level: D]
Development motor lock signal stays low more than 1 second in development motor on condition.

Possible causes:
• Extra load in the development unit
• Development motor defective
• Main control board defective

SC 342 - Toner collection motor locked
Definition: [level: D]
The toner collection sensor output does not change (OFF/ON or ON/OFF) for more than 2.55 seconds in the toner collection motor on condition.

Possible causes:
• Toner collection sensor defective
• Toner collection motor defective
• Toner clog in the toner collection pipe

SC 343 - Toner collection bottle at improper position
Definition: [level: D]
Toner bottle set switch is off and the front door is closed.

Possible causes:
• Toner collection bottle set switch defective
• Toner collection bottle is set incorrectly

1.7 PROCESS SENSOR

SC 351 - Abnormal Vsg Detection (Vsg > 4.2V)
Definition: [level: C]
The detected Vsg value is over 4.2 V.

Possible causes:
• ID sensor defective
• Main control board defective

SC 352 - Incomplete TD sensor initial setting
Definition: [level: C]
The output voltage of the TD sensor is higher than 2.6 V or lower than 2.4 V during the developer initial setting mode. VOUT to get 2.5 V for the TD sensor output is higher than 10 V or lower than 2 V.

Possible causes:
• Connector [A] not set correctly
• Toner density sensor defective
• Abnormal toner concentration

SC 353 - Abnormal Vsp Detection (Vsp ³ 2.5 V: lighter pattern)
Definition: [level: C]
Vsp is 2.5 V or higher.

Possible causes:
• ID sensor defective
• OPC drum
• High voltage control board defective
• Poor contact of the development bias terminal [A] A176T502.wmf

SC 354 - Abnormal Vsg detection (Vsg £ 2.5 V)
Definition: [level: C]
Vsg is 2.5 V or less.

Possible causes:
• ID sensor defective
• OPC drum
• Dirty charge corona casing
• Quenching lamp defective
• Erase lamp defective
• Cleaning blade defective
• Dirty ID sensor

SC355 - Abnormal VTD detection (VTD ³ 4 V)
Definition: [level: C]
VTD is 4 V or higher.

Possible causes:
• Toner density sensor defective
• Toner concentration too low

SC 356 - Abnormal VTD detection (VTD < 0.5 V)
Definition: [level: C]
VTD is less than 0.5 V.

Possible causes:
• Toner density sensor defective
• Toner concentration is too high

SC 357 - Abnormal Vsp detection (Vsp/Vsg ³ 25%)
Definition: [level: C]
Vsp/Vsg is 25% or higher.

Possible causes:
• ID sensor defective
• OPC drum
• Dirty ID sensor

SC 358 - Abnormal Vsp detection (Vsp/Vsg < 2.5%)
Definition: [level: C]
Vsp/Vsg is less than 2.5%.

Possible causes:
• ID sensor defective
• OPC drum
• Toner scattering

SC 361 - Incomplete drum potential sensor calibration
Definition: [level: C]
When the process control initial setting is performed and a development bias of –100 V or –800 V is applied to the drum shaft, the drum potential voltage is out of these ranges: 0.1 £ V–100 £ 0.7 [V] or 2.7 £ V–800 £ 4.2 [V].

Possible causes:
• Drum potential sensor defective
• Drum shaft terminal not grounded
• OPC drum
• Main charge corona unit defective

SC 364 - Abnormal VD detection
Definition: [level: C]
VD is out of specification (VR + 770 ± 20 V).

Possible causes:
• Drum potential sensor defective
• OPC drum
• Main charge corona unit defective

SC 365 - Abnormal VL detection
Definition: [level: C]
VL is out of specification (VR + 140 ± 20 V).

Possible causes:
• Drum potential sensor defective
• OPC drum
• Main charge corona unit defective
• Optics too dirty


SC 366
Definition: [level: C]
VR is larger than 360 V in the process control initialization.

Possible causes
• OPC drum
• Drum shaft terminal not ground

1.8 TRANSFER CURRENT

SC 402 - Transfer current leakage
Definition: [level: D]
When the transfer power pack output voltage exceeds 4.5 kV for 200 ms or more, the output current is multiplied by 0.8. If this condition occurs 11 time in a row, an SC is displayed.

Possible causes:
• Transfer belt defective
• Transfer power pack defective
• Poor contact at transfer bias roller, discharge plate terminals

1.9 DRUM

SC 440 - Abnormal main motor speed
Definition: [level: D]
Lock signal stays low in the main motor on condition for 1.0 second or more.

Possible causes:
• Main motor defective

SC 442 - Drum thermistor open
Definition: [level: D]
The drum thermistor is open.

Possible causes:
• Drum thermistor defective

1.10 PAPER FEED

SC 500 - Abnormal manual feed drive motor speed
Definition: [level : D]
Lock signal stays low in the manual feed motor on condition for 1.0 second or more.

Possible causes:
• Manual feed motor defective

SC 501 - Abnormal paper feed drive motor speed
Definition: [level: D]
Lock signal stays low in the paper feed motor on condition for 1.0 second or more.

Possible causes:
• Paper feed motor defective
• Paper feed control board defective

SC 502 - Abnormal 1st lift motor movement
Definition: [level: B]
The 1st lift sensor detects high condition for 10 seconds or more after the 1st lift motor starts. The first time, after the paper tray is opened and closed, the 1st lift motor starts again. If the above condition occurs twice, this SC is displayed.

Possible causes:
• 1st lift sensor shorted
• 1st lift motor defective
• Paper feed control board defective

SC 503 - Abnormal 2nd lift motor movement
Definition: [level: B]
The 2nd lift sensor detects the high condition for 10 seconds or more after the 2nd lift motor starts. The first time, after the paper tray is opened and closed, the 2nd lift motor starts again. If the above condition occurs twice, this SC is displayed.

Possible causes:
• 2nd lift sensor shorted
• 2nd lift motor defective
• Paper feed control board defective

SC 504 - Abnormal 3rd lift motor (1.5 k LCT motor for A096 copier) movement
Definition: [level: B]
The 3rd lift sensor detects the high condition for 10 seconds or more after the 3rd lift motor starts. The first time, after the paper tray is opened and closed, the 3rd lift motor starts again. If the above condition occurs twice, this SC is displayed.

Possible causes:
• 3rd lift sensor shorted
• 3rd lift motor (1.5 k LCT motor for A096 copier) defective
• Paper feed control board defective

SC 506 - Abnormal 3.5 k LCT motor movement
Definition: [level: B]
The LCT lift sensor detects the low condition for 10 seconds or more after the LCT motor starts. The first time, after the LCT cover is opened and closed, the LCT motor starts again. If the above condition occurs twice, this SC is displayed.

Possible causes:
• LCT motor defective
• LCT lift sensor shorted

SC 507 - Abnormal 3.5 k LCT feed motor movement
Definition: [level: B]
The LCT feed motor is locked for 1 second or more after this motor starts.

Possible causes:
• LCT feed motor defective

SC 508 - Abnormal tandem rear fence drive motor movement
Definition: [level: B]
It takes 10 seconds or more for the rear fence return sensor to detect the on condition after the rear fence drive motor starts. It takes 10 seconds or more for the rear fence home position sensor to detect the on condition after this fence starts moving to the home position. When the tray is set, the rear fence return sensor and the rear fence the home position sensor are on.

Possible causes:
• Rear fence drive motor defective
• Rear fence HP sensor defective
• Rear fence return sensor defective

SC5 10 - Abnormal tandem side fence home position detection - stays off
Definition: [level: B]
When the side fence goes back to the home position or the side fence drive motor works to open the fence, the side fence positioning sensor does not detect the on condition for 5 seconds or more.

Possible causes:
• Side fence drive motor defective
• Side fence positioning sensor open

SC 511 - Abnormal tandem side fence home position detection - stays on
Definition: [level: B]
When the side fence goes back to the home position or the side fence drive motor works to close the fence, the side fence positioning sensor stays on for 5 seconds.

Possible causes:
• Side fence drive motor defective
• Side fence positioning sensor shorted

1.11 DUPLEX

SC 520 - Abnormal fusing/duplex drive motor movement
Definition: [level: D]
The lock signal stays low for 1.0 second after the fusing/duplex drive motor starts.
Possible causes:

• Fusing/duplex drive motor defective
• Cleaning roller is too dirty and applies a great load to the fusing/duplex drive motor.

SC 522 - Abnormal jogger home position sensor detection - stays off
Definition: [level: B]
The jogger home position sensor does not detect the on condition for 5 seconds or more after the fusing/duplex drive motor starts.

Possible causes:
• Jogger motor defective
• Jogger HP sensor open

SC 523 - Abnormal jogger home position sensor detection - stays on
Definition: [level: B]
The jogger home position sensor does not detect the off condition for 1 second after its sensor detects the on condition in the initializing mode.

Possible causes:
• Jogger drive motor defective
• Jogger HP sensor shorted

1.12 FUSING

SC 541 - Fusing thermistor open
Definition: [level: A]
Detects the fusing thermistor open condition for 2 ms or more after turning the main switch on.

Possible causes:
• Fusing thermistor open
• Optics control board defective

SC 542 - Start key stays red
Definition: [level: A]
The fusing temperature does not reach the specified temperature after 5 minutes from turning the main switch on.

Possible causes:
• Fusing lamp defective
• AC Drive board defective
• Fusing thermistor defective

SC 543 - Fusing overheat (detected by the main control board)


SC 544 - Fusing overheat (detected by the optics control board)
Definition: [level: A]
The fusing temperature stays over 231°C for 5 seconds.

Possible causes:
• AC drive board defective
• Fusing thermistor defective
• Optics control board defective
• Main control board defective

SC 545 - Low fusing temperature (detected by the main control board)

SC 546 - Low fusing temperature (detected by the optics control board)
Definition: [level: A]
The fusing temperature stays lower than 100°C for 5 seconds after the machine becomes ready.

Possible causes:
• Fusing thermistor defective
• AC drive board defective
• Fusing lamp open
• Main control board defective
• Optics control board defective

SC 547 - Fusing lamp continuously lit
Definition: [level: A]
Fusing lamp continuously lights for 70 seconds after the machine becomes ready. However, if the door is open, paper jams, or the fusing unit is out of position, the ready condition is canceled and the main relay opens.

Possible causes:
• AC drive board

SC 548 - Unstable fusing temperature
Definition: [level: A]
If the fusing temperature changes by 21°C/second four times in 1 minute, this SC is displayed.

Possible causes:
• AC drive board defective
• Thermistor defective

1.13 SYSTEM CONTROL

SC 600 - Communication error (main control board and operation panel)
Definition: [level: D]
The main control board does not communicate with the operation panel.

Possible causes:
• Main control board defective
• Operation panel defective
• Harness defective

SC 601 - Communication error (main control board and optics control board)
Definition: [level: D]
The main control board does not communicate with the optics control board.

Possible causes:
• Main control board defective
• Optics control board defective
• Harness defective

SC 603 - Main control board malfunction (CPU)
Definition: [level: D]
Communication to the main control board is not completed.

Possible causes:
• Main control board defective

SC 620 - Communication error (main control board and DJF/RDH main board)
Definition: [level: B]
The main board does not communicate with the DJF/RDH main board.

Possible causes:
• Main control board defective
• DJF/RDH main board defective
• Harness defective
• Fiber optics defective

SC 621 - Communication error (main control board and sorter staplers/finisher main board)
Definition: [level: D]
The main control board does not communicate with the sorter stapler/finisher main board.

Possible causes:
• Main control board defective
• Sorter stapler/finisher main board defective
• Harness defective
• Fiber optics defective

1.14 DUAL JOB FEEDER/RECIRCULATING DOCUMENT HANDLER

SC  700 - Abnormal DJF/RDH feed-in motor movement
SC  701 - Abnormal DJF/RDH transport belt motor movement
SC  702 - Abnormal DJF/RDH feed out motor movement
SC  703 - Abnormal RDH inverter motor movement

Definition: [level: B]
Encoder pulse is not detected by the DJF/RDH main board in the main motor on condition. The first time, a jam occurs. The second time, an SC is displayed.

Possible causes:
• DJF/RDH feed motor defective
• DJF/RDH transport motor defective
• DJF/RDH feed out motor defective
• DJF/RDH inverter motor defective

1.15 FINISHER/SORTER STAPLER

SC 730 - Abnormal *transport motor sorter stapler/finisher) movement
Definition: [level: D]
When the encoder pulse is not detected by the SS (or finisher) main board for 200 ms after the *transport motor starts, a jam is displayed. If this occurs twice, an SC is displayed.

Possible causes:
• *Transport motor
Sorter Stapler Finisher
* Main motor Transport drive motor

SC 731 - Abnormal bin drive (lift) motor movement (sorter staplers)
Definition: [level: B]
If the wheel sensor (bin lift timing sensors) is not off after 2 seconds from when the bin drive (lift) motor stars, jam "R2" is indicated. If the wheel sensor (bin lift timing sensors) is not on after 2 seconds from when the wheel sensor (bin lift timing sensors) detects off, jam "R2" is indicated.
If the condition above occurs twice, an SC is displayed.

Possible causes:
• Wheel sensor (bin lift timing sensors) defective
• Bin drive (Lift) motor defective

SC 732 - Tray shift motor (finisher)
Definition: [level: B]
The shift tray half turn sensor does not detect the on condition for 2 seconds after the finisher tray shift motor starts. The first time, a jam is indicated. The 2nd time, an SC is displayed.

Possible causes:
• Tray shift motor defective
• Shift tray half turn sensor defective

SC 733 - Shift tray lift motor (finisher)
Definition: [level: B]
The stack height sensor 1 or 2 do not detect the on condition for the specified time after the finisher shift tray lift motor.

Possible causes:
• Shift tray lift motor defective
• Stack height sensor 1 or 2 defective

SC 735 - Abnormal jogger motor movement (sorter staplers/finisher)
Definition: [level: B]
When the jogger moves back to the home position, the jogger home position sensor does not detect the on condition within 650 pulses. Then, a jam is indicated. When the jogger moves from the home position forward, and moves back to the home position, the jogger home position sensor does not detect the on condition within 100 pulses. Then, a jam is indicated.
If the above condition occurs twice, an SC is displayed.

Possible causes:
• Jogger motor defective
• Jogger home position sensor defective

SC 737 - Abnormal gripper motor movement (sorter staplers)
Definition: [level: B]
When the gripper moves to the staple position, the gripper home position sensor does not detect the on condition. Then a jam is indicated. When the gripper moves from the staple position to the bin position, the gripper home position sensor does not detect the on condition within 1070 pulses. Then a jam is indicated. When the gripper moves to the home position, the gripper home position sensor does not detect the on condition within 1.25 seconds. Then a jam
is indicated. When the gripper moves from the home position forward, and moves back to the home position, the gripper home position does not detect the on condition within 500 ms or more. Then a jam is indicated. If the above condition occurs twice, an SC is displayed.

Possible causes:
• Gripper motor defective
• Gripper home position sensor defective

SC 738 - Abnormal staple motor movement (sorter staplers)
Definition: [level: B]
The staple home position sensor does not detect the on condition within 600 ms after the motor starts. Then a jam is indicated. If this occurs twice, this SC is displayed.

Possible causes:
• Staple unit (staple motor) defective
• Staple is jammed in the staple unit.

SC 740 - Abnormal staple unit drive motor movement (sorter stapler/finisher)
Definition: [level: B]
The staple unit home position sensor does not detect the on condition when the staple unit is in the home position. A jam is indicated. The staple unit home position sensor does not detect the on condition (within 1640 pulses) when the staple unit moves to the home position. A jam is indicated. The staple unit home position sensor does not detect the on condition (within 280 pulses) when the staple unit moves forward from the home position and moves back to the home position. A jam is indicated. If the above condition occurs twice, this SC is displayed.

Possible causes:
• Staple unit drive motor defective
• Staple unit home position sensor defective

SC 741 - Abnormal bin rear plate motor movement (sorter stapler)
Definition: [level: B]
When the rear bin plate is open, the bin rear plate open sensor does not detect the on condition for 750 ms or more after the motor starts. Then a jam is indicated. When the rear bin plate is closed, the bin rear plate home position sensor does not detect the on condition for 750 ms or more after the motor starts. Then a jam is indicated. In the initial condition, the bin rear plate open sensor does not detect the on condition for 1.25 seconds or more after the motor starts. Then a jam is indicated.  If the above condition occurs twice, this SC is displayed.

Possible causes:
• Bin rear plate drive motor defective
• Bin rear plate open sensor defective
• Bin rear plate home position sensor defective

SC 742 - Abnormal stack feed out motor movement (finisher)
Definition: [level: B]
No encoder pulses is detected for 500 ms. or more.

Possible causes:
• Stack feed out motor defective

SC 743 - Punch motor abnormal (sorter stapler with punch)
Definition: [level: B]
When turning on the main switch, the punch home position sensor is not activated within 1100 pulses. Then an R2 jam is indicated. In punch mode, the punch home position sensor is not activated within 950 pulses after rotating the punch motor. Then an R2 jam is indicated. If
the above condition occurs twice, this SC is displayed.

Possible causes:
• Punch motor
• Punch home position sensor

SC 744 - Staple jam release abnormal (sorter stapler)
Definition: [level B]
In the initial condition the paper sensor is activated and the staple home position sensor is de-activated. Then, an R3 (staple) jam is indicated. If this condition occurs 4 times in a row, this SC is displayed.

Possible causes:
• Stapler

1.16 OTHERS

SC 900 - Total counter failure (staying in the off condition)
Definition: [level: D]
The total counter stays in the off condition.

Possible causes:
• Total counter defective

SC 901 - Total counter failure (staying in the on condition)
Definition: [level: D]
The total counter stays in the on condition.

Possible causes:
• Total counter defective SC full used toner bottle
Definition: [level: A]
The toner overflow switch is activated.

Possible causes:
• Toner collection bottle is full
• Toner overflow switch defective

NOTE: Clear the SC full used toner bottle as follows:
1) While the main switch is on, open the front doors then take out
the toner collection bottle (used toner bottle).
2) Remove the toner collection bottle then empty and clean the
bottle.
3) Install the empty toner collection bottle.
4) Close the front doors.

SC 940 - Main Switch Abnormal (U.S.A. version only)
Definition: [level: A]
The Main switch does not turn off after sending the reset signal two times in a row.

Possible causes:
• Main switch
• Main PCB

Download : ERROR SC CODE RICOH

Source Url: http://ricohservice.blogspot.com/

Related articles

• How to Install a Ricoh Scanner Driver

Error E020-0000 Canon ir4570

By photocopy canon | At Saturday, April 21, 2012 | Label : Kode Error Fotocopy | 11 Comments

Error E020-0000 Canon ir4570 kesalahan ini terjadi jika sensor toner mendeteksi tidak adanya toner di Devloping Assy. Kode error ini akan ditampilkan setelah jangka waktu tertentu sensor mendeteksi kondisi seperti diatas.

output dari sensor ini di control dari DC controller PCB. Dalam hal ini, output sensor toner ditunjukkan di Devloping Assy. Kode error E020-0000 dapat terselesaikkan dengan mengganti PCB DC Controller ini

The sub-hopper motor M12 would not turn on in service mode or when running copies. As a result, the developing assembly would run out of toner. Tried replacing the Hopper Assembly, Developing Assembly and DC Controller with no change.
Link Source :http://www.copytechnet.com/forums/canon/7278-what-e000020-0000-a.html

Ganti PCB Power Suply Controller. PCB ini mengendalikan 3.3V, 5V, 13V dan 24v ke DC Controller. Part Number adalah FM2-2764-000.

Title : Kode Error E020-0000 Canon ir4570 
Tag  :  kode error, error code, photocopy, fotocopy canon, canon ir4570, mesin fotocopy

Error Solution Canon Ir4570

By photocopy canon | At Sunday, February 12, 2012 | Label : Canon , IR , Ir 4570 , Kode Error Fotocopy | 18 Comments

Error Code Canon Ir4570

Product : imageRUNNER 4570 series
Title : E000
Error : There were several symptoms

1st symptom was an intermittent error code of  E000, sometimes the machine would run as many as 20k before the problem would re-occur.

2nd symptom was the fixing film could be caked with toner.

3rd and most common symptom was that the latch would catch when opening the Main Right Side Door, this can be remedied by adjusting the cover that can interfere with the fuser release (1 screw ) (this cover is added when installing the internal finisher).  The common mistake in the field is to bend this latch instead of adjusting the cover.

Workaround :
Problem was that the latch that releases and applies pressure to the fixing film had been bent causing this mechanism to work erratically (proper and improper pressure when the Main Right side door was closed ).

Solution was to replace the latch which is formally called the Hook Holder Unit;

Part # FM2-0355-000
Product : imageRUNNER 2230 / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3570 / 4570 Title : E001 Error Code That is Not Resetable
Error :
When the machine powers up the E001 error code is displayed but cannot be reset.  (Note: The reset procedure for an E001 code is COPIER>FUNCTION>CLEAR>ERR)

Workaround :
In this case, the Main Power Supply PCB Assembly was replaced.  The machine was powered up and the E001 code was able to be reset.  The part number for the Main Power Supply Assembly is FM2-0260-000.

Remember, if the fixing unit circuitry has an open or a short, the code may not reset.  Be sure to confirm the fixing unit wiring and try resetting the code before replacing the Main Power Supply Assembly


Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E004 Error Code
Problem :
The imageRUNNER 2270 / 2870 / 3570 / 4570 displays an E004 code. Replacement of the fuser assembly and clearing of the error code in service mode resolves the issue. After approx. one day of operation the E004 code returns. Inspection of the fuser reveals that the ceramic heater element has cracked into two or more pieces with apparent arcing from the heater element.

Solution :
To resolve this reoccuring error code it is necessary to cut all the wire ties on the wire harness running from the fuser assembly to the DC-CON PCB and Power Supply.

Product :imageRUNNER 2230/2230G/2270/2830/2870/3025/3030/3035/3045/3530/3530G/3570/4570 Title : E014-0001
Error :
E014-0001 was indicated upon start-up or when pressing the Start button. E014-0001 can be an indication of a faulty fixing motor. E014-0001 can be displayed when the drive detection signal is absent for 2 sec although detection is executed every 100msec after the start of motor rotation.


Workaround :
1. Check the fixing unit for binds or broken parts.
2. Re-fit J311, and J319 connectors of the DC Controller PCB.
3. Re-fit J1009 and J1011 connectors of the fixing motor.
4. If the symptom still occurs, replace the fixing motor with a new one.

The part number for the Fixing Motor is FK2-0367-000.
Product : imageRUNNER 2270 / 2870
Title : E020 Error Code

Problem :
E020 when copying. The sub-hopper motor M12 would not turn on in service mode or when running copies. As a result, the developing assembly would run out of toner. Tried replacing the Hopper Assembly, Developing Assembly and DC Controller with no change.

Solution :
Replace the Controller Power Supply PCB.  This PCB provides 3.3v, 5v, 13v and 24v to the DC Controller.  The part number is FM2-2764-000. It is item 15, shown below, and is located behind the Accessories Power Supply.

Product : imageRUNNER 2230 / 2830 / 3530 / 2270 / 2870 / 3570 / 4570 Title :E020-0000
Error :
The E020-0000 Error Code will occur if there is an absence of toner detected by the Developing Assembly Toner Level Sensor and a presence of toner is detected by the Hopper Toner Level Sensor.  The error code will be displayed after a specified period of time with the sensors detecting this condition.

Workaround :
The output of the sensors can be checked at the DC Controller PCB.  In this case, the sensors output indicated toner in all areas of the developing assembly.  The DC Controller was replaced and resolved the E020-0000 Error Code.

Product : imageRUNNER 2230 / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3570 / 4570 Title : E020-0000 Error Code
Error :
E020-0000 Error Code will occur if there is an absence of toner detected by the Developing Assembly Toner Level Sensor and a presence of toner is detected by the Hopper Toner Level Sensor.

Workaround :
In this case, a small piece of plastic from the toner bottle was found lodged in the developer unit auger.  With the auger blocked, the toner would not properly move to the sub hopper.  The plastic piece was removed and the toner in the developer unit was vacuumed out to prevent further contamination.  Inspection of the toner motor drive and the auger mechanism for any foreign object damage is recommended before installing a new toner bottle.

Product : iR 4570 series
Title : E024
Error :
E024-0001 Error Code: The toner level sensor has an open-circuit or is not connected.


Workaround :
E024-0001 Error Code:

Toner gets in the developing assembly toner sensor (TS1) and may be shorting out the sensor. Blow out any toner in the sensor wiring and check to see if measure resolved the symptom. The toner level sensor has an open-circuit, replace the toner sensor.
Toner Sensor  FK2-0358

However, re-attachment of the sensor also solves the symptom.

When the symptom has occurred, make the following selections in service mode [COPIER > I/O > DC-CON] and check the setting for the bit1 of [P021]. If the setting is "1", re-attach the toner sensor.

Product :imageRUNNER 2230 / 2230G / 2270 / 2830 / 3025 / 3030 / 3035 / 3045 / 3530 / 3530G / 3570 / 4570,  Finisher S-1
Title : E024 on an imageRUNNER 2230/2270/3025 series machine.
Error :
E024 on an imageRUNNER 2230/2270/3025 series machine.

Workaround :
One problem  found has been the toner sensor scraper blade in the developer not making contact with the surface of the toner sensor.  To check the toner sensor scraper blade first set up a work area.  Lay out several sheets of 11 x17 paper on the work surface.  Disassembling the developer is a messy job.  Remove the upper cover of the developer and then rotate the developer in a counter clock wise direction.  Basically the cylinder should rotate so the toner is scraped off of the cylinder by the developer blade.
If it is rotated in the wrong direction a large amount of toner will adhere to the developer cylinder and makes a mess.
The toner sensor is located on the on the outside of the developer and part of it goes through the wall of the developer unit.

Product : imageRUNNER 2230/2270/2830/3870/3530/3570/4570
Title : Error E064-0002

Error : E064-0002
The machine displays an E064-0002. The machine creates solid black copies/internal test prints from edge to edge without any blanking.

Workaround :
Check the physical connections of the primary contacts. The primary drum contact is located on the drum and makes contact with an HVT metal contact on the machine's rear. The drum's primary contact tab can be easily bent or deformed during drum replacement or removal. If it becomes bent it can cause solid black copies creating a voltage leak also causing an E064-0002. Before replacing the high voltage power supply check the contact tabs first. Reshape the contacts or replace the drum.

Product : imageRUNNER 2230 / 2230G / 2270 / 2830 / 2870 / 3530 / 3025 / 3030 / 3035 / 3045 / 3530G / 3570 / 4570
Title : Error E064-0003
Error : E064-0003

Workaround :
The E064 code with a 0003 sub code can occur if Toner gets on the Developing Bias Tab.  If  the Toner is getting on the Developing Bias Tab you should check the seal on top of the Developer.

Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E100 - 0001 and E110 - 0002
Problem :
The machine is displaying error code E100 sub code 0001 and E110 sub code 0002.  The E100 - 0001 indicates that the BD interval is outside a specified range.  The E110 -0002 indicates that the scanner motor of the laser is faulty.

The laser unit and DC controller were replaced.  The wiring for the laser unit was checked.

Solution :
The problem was that the grounding spring for the steel registration roller was not making contact with the roller.  Reformed the spring so that it made contact with the roller and the error code issue was resolved.  Please see the photo below.  The grounding spring is circled in red.
Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E100 or E110 is Shown on the Display
Error :
E100 or E110 is shown on the Display. The error points to a Laser or Laser Shutter issue. After inspecting all Laser related item it was found that the Ground Plate for the Registration Roller was not making contact.

Workaround :
Check that the ground tabs are touching the Metal Registration Roller correctly

imageRUNNER 2230 / 2830 / 3530
Title : E100, E110 Error Codes
Error :E100, E110

Workaround :
Although the Main Power Supply, Controller Power Supply, DC Controller, Laser, and Drum, were replaced for this issue, the Accessories Power Supply Pcb. resolved the problem (Part number FK2-0338-000).

Product : imageRUNNER 2270/ 2870 / 3570 / 4570
Title : E100-0001 Error Code
Problem :
The machine is displaying an E100-0001. Cleared RCON, DCON and MMI. Cut tie-wraps. The DC Controller, Laser Assembly, Main Controller, Hard Drive, Memory, Boot ROM, All Night Power Supply, Controller Power Supply and wiring harnesses to the laser were replaced with no change. Checked the laser shutter.

Solution :
When the DC Controller was replaced, the original DCON ROM was reused.

Flashed the DCON firmware and resolved the problem.
Product : imageRUNNER 3025 / 3035 / 3045 Title : E110-0001 / 0002 IntermittentProblem :
Very intermittent E110-0001 / 0002, on copies 1 code in about 150 copies. The  DC Controller, Laser, Power Supply and Main Controller have been replaced with no change in error code.

Solution :
While in process of replacing 2nd Laser assyembly, found a cut on two wires in harness to Laser causing a short circuit. Harness was repaired with electrical tape.

Product : imageRUNNER 2230 / 2830 / 3530
Title : E111 Error Code when Flashing the Machine Problem :
When trying to flash the machine, the service support tool displays an E111 error. There is also a message that says "Necessary data not found bpchost.cha files \ servicesupporttool \ bpchost.cha".

Solution :
Multiple versions of the service support tool were installed on the laptop. It is important to uninstall previous versions of the service support tool before installing a new verison of the tool.

Product : imageRUNNER 2230 / 2270 / 2830 / 2870 / 3530 / 3570 / 4570
Title :E190 and E240 Error Codes in Service Support Tool when trying to Format HDD
Problem :
After replacing the HDD, the Service Support Tool is alternately displaying E190 and E240 error codes.

Solution :
After reseating connections on the Main Controller, it was discovered the contacts on the Boot Rom were dirty. After cleaning the contacts on the Boot, as well as the socket on the Main Controller, the HDD was able to be formatted, and all files installed.

Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E191
Problem :
The machine was giving an error code of E191 which indicates an error with communication with the high-voltage power supply.  Replaced the high-voltage power supply and the DC controller pcb with no change.

Solution :
The wiring between the DC controller and the high-voltage power supply was broken.  Replace the high voltage connect cable.  Part number FM2-2819-000.  The cable is item 9 circled below.

Product : imageRUNNER 2230 / 2830 / 3530 / 2270 / 2870 / 3570 / 4570
Title :E191 Error Code
Error :E191 Error Code


Workaround :
Check for a pinched wire in the harness from Connector J404 of the High Voltage Power Supply PCB to the rear frame connector of the ImageRunner, J4001. It may be necessary to replace the High Voltage Power Supply PCB (part number: FM2-0261-000).

Please note: currently, there is no part number for the affected wiring harness
Product : imageRUNNER 2230 / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3570 / 4570 Title : E225 Occurs During the Power Up Sequence
Problem :E225 Occurs During the Power Up Sequence

Solution :
In this case, the platen glass had been reversed when being cleaned by the technician.  Make sure the platen glass has the red arrow in the rear left corner of the machine top plate.  As indicated in the picture below, the red arrow should be right above the CIS ribbon cable when the glass is installed correctly.

Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E227-0001
Problem :E227-0001 & all 24 volts are missing in machine.


Solution :
E227-0001 was caused by Main Power Supply not putting out correct voltage at J1303. After installing new Main Power Supply {FM2-0260-000} machine worked with no problems.

Product : imageRUNNER  2230 / 2230G  /  2270  /  2830  /  2870  /  3025  /  3030  /  3035  /  3045  /  3530  /  3530G  /  3570  /  4570 
Title : E240 Error only on Duplexing.
Error :E240 Error only on Duplexing. The imagerRUNNER will also lock up when the code occurs.Simplex copying works fine.

Workaround :
In this case CL6, Duplex Clutch was faulty. You can check the Duplex Clutch in Service mode in Parts check, CL > 4.

Product : imageRUNNER 3025 / 3030 / 3035 / 3045
Title : E261-0000 Error Code
Problem :
The Service Manual notes this issue as the Zero-Cross signal not detected for 500msc or more after the relay is on.

Solution :
In this case, by replacing the Main Power Supply Assembly ( FM2-0260-000 ) corrected the issue.

Product : imageRUNNER 3025 / 3030 / 3035 / 3045
Title : E261-0000 Error Code
Problem :
The Service Manual notes this issue as the Zero-Cross signal not detected for 500msc or more after the relay is on.

Solution :
In this case, by replacing the Main Power Supply Assembly ( FM2-0260-000 ) corrected the issue.

Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E291 - Network Connection Problems
Problem :
When trying to update the system software the laptop displayed the following message in the Service Support Tool interface.

E291

Check if the PC is connected to the network.
Socket Error Number:10065
Socket Error Description: No route to host.
File Name: Target Info.txt


Solution :
The laptop could ping the imageRUNNER and yet the E291 code would display when trying to download the system software.  In this case, the main controller clear was performed. (COPIER>FUNCTION>CLEAR>MN-CON)  Then, a successful system software update was able to be completed.

Note: When performing an MN-CON clear you should first generate a p-print.  (COPIER>FUNCTION>MISC-P>P-PRINT)  Upon completion of the MN-CON clear, re-enter the service mode contents listed on the p-print.

Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E292 - Service Support Tool Error
Error :When attempting to download system software, the laptop displays an E292 code.

Workaround :
The connection to the imageRUNNER was confirmed using the ping command.  In this case, the tech had registered only "English" language into the Service Support Tool.  When additionally registering the "Japanese" language in the Service Support Tool, the imageRUNNER took the download without getting the E292 code.

Product : imageRUNNER 2230 / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3570 / 4570 Title : E400-0002 on the Display
Error :The error code E400-0002 is shown on the display when trying to make copies.

Workaround :
The solution in this case was to reseat the Document Feeder-N1 interface cable AND clear RCON.

*Note* The feeder width adjustment must be done after clearing RCON.

Product : imageRUNNER 2270 / 2870 / 3570 / 4570Finisher-Q1 / Q3 Saddle Fnisher Q2 / Q4
Title : E505 Error Code
Problem :E505 is defined as a Backup Ram error.The Finisher Controller had just been replaced in response to a different error code. When attempting to adjust the Alignment Position, the Alignment Plates will not move into position.

Solution :
When replacing the Finisher Controller the following adjustments must be made:
1. Alignment Position
2. Staple Position

It was discovered that the Finisher Front Cover Switch (MS31 ) was not being actuated. Without proper activation of MS31the necessary adjustments cannot be made. After activating the Front Cover Switch The adjustments were performed, and the problem was solved.

Product : imageRUNNER 2230/2830/3530
Title : E508
Error :E508 is displayed on the control panel after installing a Q1 or Q3 finisher.

Workaround :
The only Finisher that the imageRUNNERs 2230/2830/3530 support is the Finisher S-1. This error code of E508 is not found in  the Service Manual but happens when either the Finisher Q1 or Q3 are installed on these "30" series machines. The "30" series machines do not support the Finisher Q1 or Q3.

Product : imageRUNNER 2270 imageRUNNER 2870  imageRUNNER 3570 imageRUNNER 4570 imageRUNNER 2230 imageRUNNER 2830 imageRUNNER 3530
Title : E520 sub code 8001
Error :The pick up roller will move towards the rear and start to vibrate, then the E520 is generated with the sub code 8001.

Workaround :
Replacing the offset motor resolved the E520 - 8001.

M4 Offset Motor
Part number 4K1-4053-000

Product : Finisher-T1 / Saddle Finisher-T2 / Finisher-AD1 / Saddle Finisher-AD2 / Finisher-AE1 / Saddle Finisher-AE2 / Finisher-Q3 / Saddle Finisher-Q4 / Finisher-AA1 / Saddle Finisher-AA2 / Finisher-R1 / Saddle Finisher-R2 / Finisher-Q1 / Saddle Finisher-Q2 / Finisher-Y1 / Saddle Finisher-Y2 / Finisher-N1 / Saddle Finisher-N2 / Finisher-W1 / Saddle Finisher-W2 / Finisher-H1 / Saddle Finisher-H2 / Finisher-AC1 / Saddle Finisher-AC2 / Staple Finisher-C1 / Booklet Finisher-C1 / Staple Finisher-B1 / Booklet Finisher-B1 / Staple Finisher-E1 / Booklet Finisher-E1
Title : E531 with sub code 0001 / 0002
Error : The E531 error code indicates an issue with the stapler motor or stapler home position detection sensor.

In this occurrence of the E531, the stapler will drive to the rear staple position, paper will accumulate in the operation tray and generate the E531 at the time of staple.  Staple assembly, staple harness ribbon cable and the finisher controller were replaced, the finisher continued to error with the E531.

Workaround :
It was found that MSW104, staple safety switch was not properly actuated.  The spring on the white actuator was missing.

This switch cuts 24v to the stapler motor M11 and is actuated when the swing guide is forced in the maximum open position.

A quick way to check MSW104 is from the finisher controller at J714 pins 1 & 2.  Pin 1 should read 24v constant and pin 2 will read 24v when MSW104 is actuated, and 0v when MSW104 is opened.
If pin 1 reads 24v and pin 2 reads 0v whether MSW104 is actuated or open, replace MSW104.
MSW104 part number is FH7-6379-000

Note: Due to the range of Finishers covered in this Knowledge Base article, the safety switch maybe addressed by a different identification number.  Please check the related Service Manuals & Parts Catalog for correct identificationProduct : imageRUNNER 2270 series, S1 Finisher Title : E540Error :
Error code E540. Dealer had replaced the tray harnesses and the finisher controller pcb with no change in symptom.

Workaround :
Solution was to replace the Finisher Controller FG1-1478-060 and the Stack Tray Motor (M1) 4K1-4055-000 as M1 was shorted out and causing the Finisher Controller to fail

Product : imageRUNNER 2270 / 2870 / 3570 / 4570, S1 Finisher
Title : E540 0001
Error :E540 error code with a sub code of 0001 is not listed in the service manual.

Workaround :
If this code is displayed and the bin will not lower:
Check PI 10, tray lower limit sensor operation. If defective replace the sensor.
Part # W68-5571-000

Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E540 sub code 8005
Problem : The machine is giving an E540 error code with a sub code of 8005.  This sub code is not listed in the service manual.  The error code corrections are listed in tech pub TP06 238.

The delivery tray will drive all the way to the top and then the error code will be displayed.

Solution :
Check FU3 on the upper left corner of the finisher controller.  If it checks out good, power the machine off and lower the finisher delivery tray by hand and power the machine back on.

If the fuse is blown, replace the finisher controller. 
Part number 4G1-1478-050

Product : imageRUNNER 2230 / 2270 / 2870 / 3530 / 3570 / 4570, S1 finisher, B1 tray
Title : E542
Error : An intermittent error code of E542 and sometimes E584 was present.

Workaround :
The solution to remedy both intermittent codes was to replace the B1 harness part number 4G1-2262-000

Product : imageRUNNER 2230 / 2230G / 2270 / 2830 / 2870 / 3025 / 3030 / 3035 / 3045 / 3530 / 3530G / 3570 / 4570 
Title : E542 Sub Code 8004.
Error : E542-8004 code occurs when tray B continues to drive down and binds up causing a clicking noise before the code appears.

Workaround :
In this particular case the option tray escape position sensor PI14 was faulty. Replacing PI14 part number WG8-5571-000 resolved the problem.

 Product : imageRunner 2230 / 2230G / 2270 / 2830 / 2870 / 3530 / 3530G / 3570 / 4570 imageRunner C3100 / C3170 Finisher S1
Title : E584 Codes
Problem : If the Optional Bin B1 is installed, various Error Codes may result if the Finishers cover screws are not all installed and fully tightened

Solution :
The covers on the Finisher S1 and P1 are an important part of the Finisher frame, if all the cover screws are not installed and tightened the frame will flex excessively. The most common problem when the optional Tray- B1 is installed is that the shutter will intermittently contact the upper or lower bin resulting in a loud noise and / or E584 Codes.

Product : imageRUNNER 2270 / 2870 / 3570 / 4570 Finisher Q3 Punch Unit R1
Title : E593-8002
Error : E593-8002

Workaround :
In this case it was found that there was packing material left in the Punch Unit R1 during a new install. Upon the removal of the packing material the Punch Unit was able to move freely and the error code was resolved.

Product : imageRUNNER 3025 / 3030 / 3035 / 3045
Title : E602 - 0105
Problem : The machine is displaying an error code of E602 with a sub code of 0105.  This sub code is not found in the service manual.  Typically, an E602 indicates and error with the hard drive.

Solution :
Replaced the SDRAM on the Main Controller and the issue was resolved. 
Part number WA7-4625-000.

 Product : ImageRUNNER 2230/2230G/2270/2830/2870/3530/3025/3030/3035/3045/3530G/3570/4570
Title : E602-0105
Problem : Error code E602-0105, replacement of the Hard Drive,  reloading SSW  and reformatting Hard Drive does not resolve the error code.

Solution :
The Hard Drive was corrupt and was corrupting the main controller and would corrupt any new Hard Drive that was replaced into the machine and if that Hard Drive was tested into another machine it took out that Main Controller also. To resolve this issue the Hard Drive and the Main Controller had to be replaced as a set, format the HDD and load SSW.

Product : imageRUNNER 2230 / 2830 / 3530 / 2270 / 2870 / 3570 / 4570
Title :E610 Error Code
Error : E610

Workaround :
The E610 error code is generally associated to an imageRUNNER equipped with a security kit.  The security kit is LMS activated, but also contains an Expansion Bus Board and a USB Application Interface Board which connects to the main controller.  If the Expansion Bus Board or USB Application Interface Board is removed or has a loose connection to the main controller, an E610 error code may be generated.

Reset and / or reinstall the Expansion Board and the USB Application Interface Board to resolve the E610 code.

Product : imageRUNNER 3030/3035/3045
Title : E611-0000 is on the display
Error : E611-0000 is on the display. The code usually would happen sporadically.

Workaround :
In this case, clearing sectors of the HDD resolved the issue. There have also been some instances where clearing the MNCON has also resolved this error code. A definition of this code is not found in the this product series documentation. Below is a description of the code:

E611-0000
Error in repeat of reboot due to fault of the SRAM, etc.

SRAM information has failed, job information stored in the SRAM cannot be read and a reboot is repeated at recovery from powering off

Product : imageRUNNER  2230/2270/2830/2870/ 3530 /3570/ 4570
Title : E674-0008
Error : Although the error code of E674 is documented in the Service Manual, the sub code of 0008 is not. In this case, the machine was displaying an E674-0008.

The Service Manual describes that an E674 is related to a communication fault between the multi line fax pcb and the Main Controller pcb. When looking in Service Mode>Copier>Display>Version>Fax, the machine displayed, a "??#" for the version of the fax. The machine in this case was flashed. Other symptoms experienced were, no dial tone when using the "On-Hook" key using the fax function, the machine could not print any internal/external prints,  the machine could not complete the "forced shut down procedure" and would "lock up".  Although these symptoms were experienced, the machine was able to copy without problems.

Workaround :
Following the Service Manual's instructions, the multi line fax pcb assembly was disassembled. Upon inspecting the unit, it was noticed that one of the ribbon cables on the G3 fax control pcb was not seated properly. After reseating the ribbon cables on the G3 fax control pcb, the machine stopped displaying this error code. The fax functionality then returned and the machine stopped exhibiting the other symptoms listed above. Checking and reseating the ribbon cables located on the G3 fax control pcb resolved the issue.

Related Service Manual error code information for an E674 code is:
1. sub code 0001- An attempt to set mode for the fax device has failed

Remarks for items to check are:
1. Check the connection of the cable between the fax control PCB (2 line) and the main controller PCB.
2. Replace the ROM DIMM of the fax control PCB (2-line).
3. Check ribbon cables within the fax pcb assembly.
4. Replace the fax control PCB (2 line).
5. Replace the main controller PCB.

Product : imageRUNNER  2270 / 2870 / 3570 / 4570  imageRUNNER 2230 / 2830 / 3530 
Title : E716 error code
Error : Error code E716 occurs with the Finisher-S1 is installed. The error code refers to the Cassette Feeding Unit-Y2, which may not be installed. If the Finisher-S1 is disconnected the error code will clear.

Workaround :
If the error code E716 is present upon install of a iR XX30 series machine, make sure a 3-Way Unit-A1 is installed.  See KB article 54256 for further information.

If the error code E716 is generated on a iR XX30 or iR XX70 series unit:

Check to see if the error clears when the Finisher-S1 is removed.  If the error clears, check for 13VA2 and 24VA going to the 3-way unit-A1.  The 13v & 24v is can be checked at J646 of the Accessory Power Supply, pin 1 (13v), pin 3 (24v) to J741 of the 3 way unit-A1, pin 7 (13v), pin 9 (24v).  If the voltage is present, replace the 3 way unit-A1 controller.  PN:  FM2-3221-000.  

Product : iR4570 series
Title : E732
Error : E732-0001 can be displayed when the DDI-S communication error occurs, meaning the communication betwen the Reader and MCON.

Workaround :

1. Re-insert the connector J1014 ( reader wire harness for DDI communication) on the Main controller PCB.
2. If the symptom still occurs, pull the memory and DIMM connected to the main controller PCB (J1004) and the DC controller PCB (J381).Clean the contacts with a clear rubber erasure and re-insert the DIMM connected to the main controller PCB (J1004) and the DC controller PCB (J381).
3. If the symptom still occurs, replace the Reader Controller PCB with a new one.  FG3-3765-000 = Reader Controller PCB Assemb

Product : imageRUNNER 2270 / 2870 / 3570 / 4570
Title : E733 Error Code After Replacing the Boot Rom
Error : A new boot rom was inserted into a slot and the machine was turned on.  The E733 came up on the display after a few minutes.

Workaround :
In this case, the boot rom was mistakenly placed in the slot located on the DC Controller.  The Boot Rom slot on the Main Controller is the same size as the DCON Dimm slot on the DC Controller.  Hastily replacing this chip without confirming the correct slot will damage the chip.  NOTE: If you are installing a network boot rom and it is damaged, you will need to contact the TSC for the replacement procedure.

Product : imageRUNNER 2230 / 2830 / 3530 / 2270 / 2870 / 3570 / 4570 Finisher-S1
Title : E733-0001 Error Code
Error : The imageRUNNER is displaying an error code of E733-0001. The code is consistent, and will occur when an attempting to make a copy. After the start key is pressed, the paper will feed to the registration roller, and the imageRUNNER will go into code.

Workaround :
An E733-0001 indicates a communication problem, usually between the DC and Main Controller. In this example the problem was rectified by replacement of the Finisher Controller. A possible scenario, would be to disconnect the finisher to observe a change in symptom. If the imageRUNNER will output paper, or at least feed paper past the previous point, the problem may lie in the finisher.

S1-Finisher Controller P/N - 4G1-1478-060

Product : imageRUNNER 2230 / 2830 / 3530 / 4530
Title : E744-1000
Problem : While flashing machine, power in office shut off while writing to Boot-rom. After rebooting machine, could not write software to Boot-rom.

Solution :
Boot-rom software was damaged during power failure. Part number for Boot-rom is FM2-3803-600.Product : imageRUNNER 2270 / 2870 / 3570 / 4570 Title : E749Error :
E749 in Error History.

Workaround :
An E749 is in the error history after installing / uninstalling a Printer Kit or MEAP device in the iR2270, 2870, 3570, 4570. This error only occurs once when this type of installation has been done.This error may only be displayed in history and not on the LCD Display.Cycle the power of the machine after installation of these options.

Product : imageRUNNER 2230 / 2270 /2830 / 2870 / 3530 / 3025 / 3030 / 3035 / 3045 / 3570 / 4570 / 3225 / 3230 / 3235 / 3245
Title : E805
Error : E805

Workaround :
It has been found that the exhaust fan can become dirty or locked up.  Clean the fan and make sure the fan blades spin freely.  In some cases the fan needs to be replaced.  Fan part number is (FK2-0360-000) for both fans.

Labels: canon imagerunner error codes IR 3035 * 3045 * 3530 * 3530G * 3570 * 4570 2525 * 2530 * 2535 * 2535i * 2545 * 2545i canon copier
canon error codes e602 e540 e001 e000 e732 copiers copy machine
canon imagerunner error codes IR 3035 * 3045 * 3530 Canon Copie

Error codes for Canon IR 
canon imagerunner 330 400 ir210 gp210 gp200 ir200 ir 330 ir330 ir 400 
canon copier canon copy machine 

• "E000"Fixing temperature fails to rise 
• "E001"Fixing temperature rises abnormally 
• "E002"Fixing temperature fails to reach a specific value 
• "E003"Fixing temperature drops abnormally
• "E007"Fixing film has become displaced 
• "E010"The main motor fails to lock 
• "E030"Total counter failure 
• "E031"Option counter failure 
• "E032"The copy data controller counter is faulty 
• "E051"The horizontal registration home position detection mechanism fails 
• "E064"The high voltage (primary charging, transfer charging, developing) output is faulty 
• "E100"BD Error 
• "E110"The laser scanner motor fails to lock 
• "E190"RAM error 
• "E191"Communication error between the DC controller & composite power supply
• "E202"Scanner home position cannot be detected 
• "E220"Scanning lamp fault 
• "E240"Communication error in the DC controller 
• "E243"Communication error between control panel & image processor PCB 
• "E261"Error in the zero cross signal 
• "E301"Intensity of scanning lamp is not correctly adjusted 
• "E400"Communication error between copier and RDF-G1 
• "E401"Pick up error in RDF-G1 
• "E402"Belt drive fault in RDF-G1 
• "E403"Feeder fault in RDF-G1 
• "E411"Original tray paper sensor/ registration sensor in RDF-G1 
• "E422"Communication error between copier and ADF-F1 
• "E710"Error in IPC communication 
• "E711"Error in IPC communication 
• "E712"Error in communication with the feeder 
• "E713"An IC error has occured (sorter) 
• "E716"Communication error with the pedestal 
• "E717"Communication error with the copy data controller 
• "E803"Error in the output voltage of the composite power supply PCB 
• "E901"Pedestal motor or controller PCB

ERROR CODE COPIER CANON
Canon Copier error codes Canon IR imagerunner 2200 2800 3300

1. E000 Fuser problem, Fuser heater, Fuser film, Thermistor, Connections, Power Supply 
2. E001 Fuser Temperature too high, Fuser heater, Fuser film, Thermistor, Connections, Power Supply
3. E002 / E003 Low Fuser Temperature, Thermistor, Fuser heater, Fuser film, Connections, Power Supply
4. E004 Fuser problem, triac shorted, thermistor, power supply 
5. E007 Fuser film rotation problem ( IR 2200, 2800, 3300 or i ) 
6. E009 Fuser does not match power supply or DC controller board 
7. E010 Drive problem, main motor, motor drive board, mechanical gear functions 
8. E014-0000 Fuser motor ( IR 2200, 2800, 3300 or i ) 
9. E019-0000 Waste toner full ( IR 2200, 2800, 3300 or i ) 
10. E032-0001 DA unit communications error ( IR 2200, 2800, 3300 or i ) 
11. E040 Holding plate drive assembly, holding plate position sensor or holding plate solenoid 
12. E043 Paper deck feed motor problem 
13. E051-0000 Horizontal registration home detect mechanism ( Motor M9 or sensor PS10 ) ( IR 2200,
14. 2800, 3300 or i )
15. E054 Duplex feed roller home position sensor lever, duplex feed roller gear, duplex drive board,duplex feed clutch, or duplex motor
16. E055 Horizontal registration guide, home sensor lever, drive gear, duplex drive board, horizontal registration motor or duplex drive motor
17. E064-0000 Charge, transfer or developer bias problem 
18. E100 Laser unit, BD mirror, image processor board, laser board, DC controller, can also happen if drum is not installed 
19. E102 Laser problem 
20. E110-0000 Laser motor ( IR 2200, 2800, 3300 or i ) 
21. E202-0001 Scan problem, scan switch, scan motor, image processor board ( IR 2200, 2800, 3300 or i ), panel locked with error message
22. E203 Scan motor driver board, scan motor or reader controller board 
23. E204-0001 ADF lead edge image signal problem ( IR 2200, 2800, 3300 or i ) 
24. E211/215 Reader controller board, exposure lamp heater, exposure lamp thermistor, flat cable connections.
25. E216 Exposure lamp, inverter board, reader controller board 
26. E217 Exposure lamp heater or heater controller board 
27. E219 Exposure lamp, inverter board, reader controller board 
28. E220-00001 Exposure lamp inverter board ( IR 2200, 2800, 3300 or i ) 
29. E225-0000,-00002 White plate/edge whit plate read error, bad CCD or exposure lamp ( IR 2200, 2800, 3300 or i )
30. E240-0000 Mcon-Dcon problem, bad DC controller ( IR 2200, 2800, 3300 or i ) 
31. E243-0000 Control panel to image processor board communication problem,main controller board

unique error code : VCW3SD4JFW2M